Storage.mod Question

[gray]

I am baffled by the following behaviour (Cortex M3, STM32F207 target). Here's a minimal test case, condensed and abstracted from my actual code.

Code: Select all

MODULE testalloc;
  IMPORT Main, Out;

  TYPE
    P = POINTER TO Pdesc;
    Pdesc = RECORD i: INTEGER END;

  VAR
    p: P;

BEGIN
  NEW(p);
  p.i := 13;
  Out.Int(p.i, 0); Out.Ln
END testalloc.

As you'd expect, I get "13" in the terminal. So far, so good. Now I import also 'Storage':

Code: Select all

MODULE testalloc;
  IMPORT Main, Out, Storage;
  (* ... same as above *)

Now I get no output at all, and no rt-error either. Either I miss something, or things go haywire somehow. I don't know how 'p' is represented internally, but if I assume it's an address, I can check if it's within the heap boundaries:

Code: Select all

(* ... as above *)
BEGIN
  NEW(p);
  Out.Hex(SYSTEM.VAL(INTEGER, p), 0); Out.Ln;
  p.i := 13;
  Out.Int(p.i, 0); Out.Ln
END testalloc.

Without 'Storage' imported, I get '20000220H', with 'Storage' I get '20000204H', which both look OK with a heap starting at '20000200H' (assuming 'p' actually represents an address, ofc).

[cfbsoftware]

I have not been able to reproduce the problem here.

1. Have you modified Storage.Mod?

2. Try running the attached program and compare its output with:

Capture.JPG (18.03 KiB) Viewed 31834 times

If they do not match check your Configuration file against the default supplied with Astrobe.

[gray]

1. No, I have not modified Storage.mod.

2. The config is the stock one, aside from the library search paths.

3. When I run your program with the stock Main.mod, I get the same memory values as you.

4. However, I use a slightly modified Main.mod, as well as a modified Serial.mod (Serial2.mod, allowing the parallel use of both serial ports. Note that the changes to both modules are experimental as of now (or hacks, less euphemistically), and not yet clean implementations, but done with as few as possible changes). With this setup, I get different memory values with your program.

output.png (4.03 KiB) Viewed 31830 times

Observation: Serial2.mod uses NEW(), but 'HeapUsed' reported by Storage is 0H nonetheless.

[cfbsoftware]

Observation: Serial2.mod uses NEW(), but 'HeapUsed' reported by Storage is 0H nonetheless.

Thanks for pointing that out. Storage initialises the heap. You need to make sure that it is loaded *before* any calls to NEW. One way to do this is to add it to the IMPORT list in the first module that calls NEW.

P.S. I had to remove your modules.zip attachment as it contained a significant amount of source code which can only be shared with other Astrobe Personal and Professional users. It is OK to republish snippets, or changes that are substantially yours - in this case the following would have been sufficient:

Code: Select all

TYPE
  Serial* = POINTER TO SerialDesc;
  SerialDesc = RECORD
    SR : INTEGER;
    DR : INTEGER;
    CR1: INTEGER;
    CR2: INTEGER;
    CR3: INTEGER;
    BRR: INTEGER
  END;

PROCEDURE SetUsartNo(usartNo: INTEGER): Serial;
  VAR
    s: Serial;
    USARTBase: INTEGER;
BEGIN
  NEW(s);
...

PROCEDURE Open*(usartNo, baudRate: INTEGER): Serial;
  VAR
    s: Serial;
BEGIN
  s := SetUsartNo(usartNo);
...

[gray]

Thanks.

P.S. I had to remove your modules.zip attachment as it contained a significant amount of source code which can only be shared with other Astrobe Personal and Professional users.

Oops. Sorry about that.